FAQs

A die tool is required to cut the box to its flat shape before it gets glued and folded. A die-cutting tool can vary in price based on the size of the box, the quantity, and the type of box you're looking to make.

If you are doing a small paper board box for a cosmetic product or a product of similar size you could typically pay around $150 to $250 if the quantity of your order is low. When you reach a higher volume of boxes, we will make a multi-up die if the quantity is around 25,000 boxes or more. The more ups on a layout or the larger the surface of a die, the higher the price would be for the tool.

To create Pantone artwork with Adobe software, follow the instructions in these two articles: How to create a Pantone ink design in Adobe Illustrator
How to create a Pantone ink design in Adobe InDesign

You can add custom quantity in the pricing chart. There is a field called Add Custom Quantity (see below). Type in the desired quantity and press the green plus button. It will appear in the chart.

-

Flexo corrugate die are much larger in size and has a cylindrical shape to them which makes them more costly to make. Whereas a flat sheet die that runs on letterpress up to a Bobst platten die cutter can be produced much quicker and cheaper than a cylindrical die tool.

There are several different binding options to choose from: Saddle Stitching: This is one of the most economical options and best suited to booklets with lower page counts. This is because the sheets are gathered, folded, and staples on the spine, and in booklets, with more than 60 pages the pages tend to "bubble" at the spine and not lay perfectly flat. Spiral Binding: The pages are punched and wound onto a plastic spiral, this allows the pages to open 360 degrees. As the coil comes in a range of size this option is better able to accommodate larger page counts while still being a relatively economical option. Wire-O Binding: Wire-O is similar to spiral binding, except instead of a plastic...

The main difference between Self Cover and Plus Cover is the paper that the cover portion is printed on. Plus Cover booklets have the cover portion printed on a different paper than the inside pages, whereas Self Cover booklets have the cover printed on the same paper as the rest of the booklet. A Plus Cover booklet allows for special finishes and the use of a thicker stock on the cover, however, the cover has to be run separately from the insides. This makes Self Cover the more economical option.

The easiest way to think about pages is to think about a PDF document with multiple pages. Each page in that PDF document would be equivalent to one page in the finished, bound book. A sheet is what the pages are printed on. For saddle stitching, a sheet has 4 pages on it, and therefore the page count must be divisible by 4. For Spiral, Wire-O, Perfect Binding, and Corner Stapling, a sheet has 2 pages.

Yes, we ship to rural and remote areas.

All sizes and dimensions are displayed using the imperial system "inches". 

If you are a government department looking to produce a protected printing job with Newprint, we will require an email sent with your request for us to provide you with security clearance status.

Yes, booklets do require bleed. The standard .125" or 1/8" bleed will still be required on all edges, including the spine.

For saddle stitch booklets, a minimum of .25" on all edges would be required. For Spiral, Wire-O, and Perfect Binding, these bindings require additional margin at the spine. For Spiral and Wire-O, an additional .25" on the spine is required for the punches. For Perfect Binding, an additional .25" is also required, so that no page content ends up too close to the spine.

The best program to design books would be Adobe InDesign, as this program was specifically created to design multipage files intended to be bound in some fashion and has several useful features. These include: Facing Pages: This setting arranges the pages in "Reading View", where the front and back covers are by themselves and the rest of the pages are displayed in pairs, the way they would be when the book is printed and bound. This is especially helpful for artwork that requires "Cross-Overs" or pictures and/or design elements that cross over the spine from one page to the page next to it. Master Pages: This feature allows the designer to set up ...

empty

empty

Because of the number of operations involved with the various bindery methods, there are serval fixed set-up costs. These costs are the same regardless of the quantity being ordered. When the quantity is higher, the fixed costs are spread out over the increased quantity and therefore the unit rate decreases.

There is no difference between NCR Forms and Carbonless forms. These are just two different names for the same product. "NCR" stands for No Carbon Required, taken from the initials of its creating company, National Cash Register.

NCR and Envelopes are exceptional due to the nature of the printing process. Most NCR forms and Envelopes are printed on paper that is the finished size, and the press used requires a minimum of 0.25" of grip. For this reason, please make sure to apply 0.25" of margins to these two products. This is known as the "Print Safe Zone".